Dagryme said:Thanks for the tip, I am getting the entire dash done in leather and it will look better in brushed aluminum than in wood.
chevyguy_72 said:I am working on doing this switch out right now...
I will post the final part numbers/pics once i get all installed to verify they are correct...
One thing to be aware of is the front door window/mirror/lock/etc plates changed at some point... 07/08 are different then 2010-2013 not sure where 09 falls...
I also ordered the center console trim peice from an H2 - looks like a very close match... (Replaces black plastic on armrest area with a stainless trimmed piece)
chevyguy_72 said:Anyone have the part number for the front driver switch plate w\power folding mirrors?
My dealer has ordered 2 different ones and both have been for without power folding mirrors.
I know they exist...
lt1mcss said:This should be it 20877680
Just the trim piece $40
http://www.ebay.com/itm/SIERRA-SILVERADO-YUKON-TAHOE-LH-FRONT-METAL-BRUSH-WINDOW-SWITCH-BEZEL-20877680-/330856368547?pt=Motors_Car_Truck_Parts_Accessories&hash=item4d089389a3&vxp=mtr
With new switches $105
http://www.ebay.com/itm/GENUINE-GM-FRONT-LH-WINDOW-SWITCH-W-METAL-BRUSH-BEZEL-20877680-/230761943750?pt=Motors_Car_Truck_Parts_Accessories&hash=item35ba7bd2c6&vxp=mtr
lt1mcss said:This should be it 20877680
Just the trim piece $40
http://www.ebay.com/itm/SIERRA-SILVERADO-YUKON-TAHOE-LH-FRONT-METAL-BRUSH-WINDOW-SWITCH-BEZEL-20877680-/330856368547?pt=Motors_Car_Truck_Parts_Accessories&hash=item4d089389a3&vxp=mtr
With new switches $105
http://www.ebay.com/itm/GENUINE-GM-FRONT-LH-WINDOW-SWITCH-W-METAL-BRUSH-BEZEL-20877680-/230761943750?pt=Motors_Car_Truck_Parts_Accessories&hash=item35ba7bd2c6&vxp=mtr
That black insert is molded to the plate... I contemplated cutting it out... but decided that might not turn out so wellThomcat said:Compared the driver's bezels on my Avys...one has the power folding mirrors, the other doesn't
If you just want the bezel plate, it should be the same part with or without folding mirrors, the dimensions of the two switch blocks and bezels are identical.....the difference being that there is a black plastic insert of the same size in place of the power mirror rocker switch in the switch block without the power folding mirror
HawaiianBrian said:I did the swap a while back, it's fairly easy, just take your time and have some patience. The clips that hold these things on are pretty solid. Be prepared to pull pretty hard, the plastic will flex a little but shouldn't snap on you.The door switches are the easiest, they just pop right off with a pry tool ( flat screwdriver etc), there might be 1 screw but I don't remember. I recommend wrapping the tool and/or the edge of the piece you're working on with some painters tape to protect the edges. For the radio bezel, stick a pry tool in there, I went bottom left edge, once you get 1 popped, just keep pulling and slowly work around the edge. The dash is the same. Note that the passenger side dash is 1 long piece, includes the vent in all as 1.
That would be the best way....naylor99 said:Thanks much! I assume you'd have to remove each piece even do a vinyl wrap?
chevyguy_72 said:Dealer came back saying that wasn't a valid part number
They are now ordering 22968518
That sound right?
That black insert is molded to the plate... I contemplated cutting it out... but decided that might not turn out so well
chevyguy_72 said:Dealer came back saying that wasn't a valid part number
They are now ordering 22968518
That sound right?
That black insert is molded to the plate... I contemplated cutting it out... but decided that might not turn out so well
I appreciate the info but the dealer is picking up the tab for the parts...lt1mcss said:I googled the part number and it just said "plate" with a price of about $85-100 or so. It could be right but I couldn't find a picture. I know some of the part numbers were changed. The number i gave you is definitely a valid part number but it may direct them to the one they gave you. Honestly I would stop dealing with your "dealer" on the issue if the part they ordered is wrong again and just buy the $40 trim piece from ebay.That's why i provided it You don't need new switches, just the trim. The piece you get from the dealer is going to have the switches and the trim most likely for that price.
Finally got all of my pieces and got all installed last night... looks much better than the wood... the armrest piece shown above is a little brighter than the rest of the pieces but it is close...lt1mcss said:I decided to do a little of both vinyl and the factory brushed pieces. I got a piece of 3M 1080 Black Brushed wrap to do a couple piece to cover the 2 wood grain pieces to the left and right of the steering wheel and the passenger side piece. I'm also going to wrap the door switches with it too. I'm going to get a factory brushed radio bezel instead of wrapping that. I'm also considering doing the factory brushed GMC console insert and brushed steering wheel pieces as long as the arm rest insert someone posted earlier. I'll post some pictures when it's done. If I get the wrap Friday I'm hoping to maybe wrap my pieces over the weekend.