TrimmedOutHP500
Full Member
- Joined
- Jul 26, 2002
- Messages
- 61
I have tried using the search feature, but have come up with no luck on the these questions. ?I only have time to get on this site about once a month, so please bear with me. ?Direct links to answers are great as well. ?Thank you.
1. ?I intend to install 55w rear facing fog lights in my steps on my rear bumper. ?Can I just tap the power off of my cargo lights, so I can control these with exisitng switches, OR do I need to run a relay to a new power source lead, and just enable the relay with the exisitng cargo lights circuit? (I want to be able to turn them on and off whenever, not reverse lights. I do not want any new switches or anything).
2. ?I have 265 75 16 Coopers on ARE rims on my 2002 Avalanche 2500. ?The front T-bars are cranked up a bit. ?I have bought molded mud guards, but since my front tires already rub very slightly, on full lock reverse turns, (which I have to do sometimes towing a trailer), I am concerned about ripping off the mud guards. ?I did get the push pins from the dealer to install them with. ?ALSO, I have Westin nerf bars, and the fronts don't fit flush because of them. ?Did anyone else run across this? ?Did you just cut the mud guard around to make clearance, and if so, did you lose structural integrity of the mud guard?
3. I have the R&D kits for Fog Lights on and four headlamps on.
Which is the best and method, i.e. safest for the 4 headlights on? R&D, or the added ground wire? ?
What is the best way to set up my amber DRLs to run all the time?
4. Does anyone have issues with the rubber rear window gasket 'drooping' from the top? ?I have taken mine out, and added adhesive and tape to keep it up, however the droop is really caused by the fact the gasket is a little too big in circumference for the openning. ?Will GM balk at replacing it under warranty?
5. What is the deal with the recall on the gas filler neck on 2002 2500s? ?My dealer said they had never heard of it, but I know the problem exists. ?
6. Does anyone have a solution/product to match the front over wheel lip trim on a 2500 to the back wheel opennings without cutting/splicing pieces together?
Just additional...
Has anyone else had a spray in bed liner done? Just curious... I had a Scorpion Liner sprayed on the floor, and could not be happier with it. ?I spend most of my time tweaking my boat, and the AV gets attention as time and money allow. ?So far, I have a hybrid K&N FIPK, ?removable mudflaps, amber DRLs, 4 Silverstars, ARE Outlaw II rims, and and Cooper tires, Air Lift bags with the filler nozzles being the rear upper license plate bolts, Lund clear bug sheild, ventvisors, true duals with FLowmaster 50s coming out boat style behind the rear wheels flush with the body, HT PPIII, Catch-all molded carpet mats front & rear, billet grille and bowtie, Westin nerf bars, and a Sport Wing. ?
Thank you all so much again, for your time in answering. ?You guys know this site like the back your your hand, and all I do is search for hours with no results. ?If you have any boat questions, try www.offshoreonly.com , as I am on there everyday.
1. ?I intend to install 55w rear facing fog lights in my steps on my rear bumper. ?Can I just tap the power off of my cargo lights, so I can control these with exisitng switches, OR do I need to run a relay to a new power source lead, and just enable the relay with the exisitng cargo lights circuit? (I want to be able to turn them on and off whenever, not reverse lights. I do not want any new switches or anything).
2. ?I have 265 75 16 Coopers on ARE rims on my 2002 Avalanche 2500. ?The front T-bars are cranked up a bit. ?I have bought molded mud guards, but since my front tires already rub very slightly, on full lock reverse turns, (which I have to do sometimes towing a trailer), I am concerned about ripping off the mud guards. ?I did get the push pins from the dealer to install them with. ?ALSO, I have Westin nerf bars, and the fronts don't fit flush because of them. ?Did anyone else run across this? ?Did you just cut the mud guard around to make clearance, and if so, did you lose structural integrity of the mud guard?
3. I have the R&D kits for Fog Lights on and four headlamps on.
Which is the best and method, i.e. safest for the 4 headlights on? R&D, or the added ground wire? ?
What is the best way to set up my amber DRLs to run all the time?
4. Does anyone have issues with the rubber rear window gasket 'drooping' from the top? ?I have taken mine out, and added adhesive and tape to keep it up, however the droop is really caused by the fact the gasket is a little too big in circumference for the openning. ?Will GM balk at replacing it under warranty?
5. What is the deal with the recall on the gas filler neck on 2002 2500s? ?My dealer said they had never heard of it, but I know the problem exists. ?
6. Does anyone have a solution/product to match the front over wheel lip trim on a 2500 to the back wheel opennings without cutting/splicing pieces together?
Just additional...
Has anyone else had a spray in bed liner done? Just curious... I had a Scorpion Liner sprayed on the floor, and could not be happier with it. ?I spend most of my time tweaking my boat, and the AV gets attention as time and money allow. ?So far, I have a hybrid K&N FIPK, ?removable mudflaps, amber DRLs, 4 Silverstars, ARE Outlaw II rims, and and Cooper tires, Air Lift bags with the filler nozzles being the rear upper license plate bolts, Lund clear bug sheild, ventvisors, true duals with FLowmaster 50s coming out boat style behind the rear wheels flush with the body, HT PPIII, Catch-all molded carpet mats front & rear, billet grille and bowtie, Westin nerf bars, and a Sport Wing. ?
Thank you all so much again, for your time in answering. ?You guys know this site like the back your your hand, and all I do is search for hours with no results. ?If you have any boat questions, try www.offshoreonly.com , as I am on there everyday.