itsstopher
PM 2018
PM 2017
PM 2016
PM 2015
PM 2014
PM 2013
PM 2012
SM 2011
SM 2010
SM 2009
SM 2008
SM 2007
SM 2006
SM 2005
SM 2004
SM 2003
Full Member
Memory Seat Control Module Replacement
Removal Procedure
1. Remove the seat cushion. Refer to Seat Cushion Frame Replacement - Front .
2. Disconnect the upper electrical harness connectors (3).
3. Remove the module (2) retaining screws (1).
4. Slide the module to the right to disengage the lower retainers.
5. Disconnect the lower electrical harness connectors (2).
6. Remove the module from the vehicle.
Installation Procedure
1. Position the module into the vehicle.
2. Connect the lower electrical harness connectors (2).
3. Slide the module (2) to the left to engage the lower retainers.
Notice
Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
4. Install the module retaining screws (3). Tighten
? ? Tighten the screws to 3 N?m (26 lb in).
5. Connect the upper electrical harness connectors (3).
6. Install the seat cushion. Refer to Seat Cushion Frame Replacement - Front .
7. If a new memory seat module was installed, calibrate the seat. Refer to? ? ?
? ? Memory Seat Calibration Procedure.
Memory Seat Calibration Procedure
The memory seat module uses position sensor inputs to establish soft stop locations for the adjuster motors several millimeters ahead of the physical limits of the adjuster assembly. After replacing a memory seat module or adjuster components, it may be necessary to reset the adjuster motor soft stop locations. When the repair procedure has been completed, operate the seat adjuster switch in every direction until the seat adjuster reaches its mechanical hard stop by repeatedly pressing and releasing the switch as necessary.
Removal Procedure
1. Remove the seat cushion. Refer to Seat Cushion Frame Replacement - Front .
2. Disconnect the upper electrical harness connectors (3).
3. Remove the module (2) retaining screws (1).
4. Slide the module to the right to disengage the lower retainers.
5. Disconnect the lower electrical harness connectors (2).
6. Remove the module from the vehicle.
Installation Procedure
1. Position the module into the vehicle.
2. Connect the lower electrical harness connectors (2).
3. Slide the module (2) to the left to engage the lower retainers.
Notice
Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
4. Install the module retaining screws (3). Tighten
? ? Tighten the screws to 3 N?m (26 lb in).
5. Connect the upper electrical harness connectors (3).
6. Install the seat cushion. Refer to Seat Cushion Frame Replacement - Front .
7. If a new memory seat module was installed, calibrate the seat. Refer to? ? ?
? ? Memory Seat Calibration Procedure.
Memory Seat Calibration Procedure
The memory seat module uses position sensor inputs to establish soft stop locations for the adjuster motors several millimeters ahead of the physical limits of the adjuster assembly. After replacing a memory seat module or adjuster components, it may be necessary to reset the adjuster motor soft stop locations. When the repair procedure has been completed, operate the seat adjuster switch in every direction until the seat adjuster reaches its mechanical hard stop by repeatedly pressing and releasing the switch as necessary.