• If you currently own, previously owned or want to own an Avalanche, we welcome you to become a member today. Membership is FREE, register now!

Post the mods you want to do at the Nationals.

Loggie said:
Sail Panel LED'S

This is one we can do!!!!  I did vanthony's at Hotlanta Part Duece I'll bring all my tools to do this, just get all the goodies before you come!


http://www.ebay.com/itm/10-x-LED-5mm-PRE-WIRED-12-VOLT-WIDE-VIEW-ANGLE-RED-/321092012446?pt=LH_DefaultDomain_0&hash=item4ac293499e

http://www.ebay.com/itm/10-LED-HOLDER-RETAINERS-PANEL-MOUNTING-5mm-LOCKS-USA-/321069212251?pt=LH_DefaultDomain_0&
hash=item4ac137625b

...and you'll need 20 feet of 18 gauge speaker wire.
 
DouglasOak said:

This is one we can do!!!!  I did vanthony's at Hotlanta Part Duece I'll bring all my tools to do this, just get all the goodies before you come!


http://www.ebay.com/itm/10-x-LED-5mm-PRE-WIRED-12-VOLT-WIDE-VIEW-ANGLE-RED-/321092012446?pt=LH_DefaultDomain_0&hash=item4ac293499e

http://www.ebay.com/itm/10-LED-HOLDER-RETAINERS-PANEL-MOUNTING-5mm-LOCKS-USA-/321069212251?pt=LH_DefaultDomain_0&
hash=item4ac137625b

...and you'll need 20 feet of 18 gauge speaker wire.



Just bought 4x each so we"ll have extras  (y) (y)
 
Does anyone know the part number for HID's for the 2007 Avalanche? I found a new set out in my garage that i won at a GTG years ago when I had my 2002 Avalanche, do they take the same bulbs? If so maybe someone would help me get them put in?
 
if anything we can always pull the assembly out and look
 
Can an easy lift tailgate be done? if so any suggestions where to get the parts? thanks
 
It's a piece of cake.(y)

BnGBleeder said:
Can an easy lift tailgate be done? if so any suggestions where to get the parts? thanks
 
MS03 2500 said:
Alaska_AV. said:
dmax swap in an 07
In a 1500 frame not sure on that one.

Just need to add a Suburban 2500 frame.

I would like to do the independently wealthy mod so I can attend more GTGs.
Wish I could go, not going to happen this year.
 
I would like to change out my door speakers, for ones with LED's, not sure the wiring will be as simple as the 03 though    

DONE

Didit
 
I got a couple of spare cargo light housing if anyone needs one or want to add a second light.
 
I can't believe we all forgot this one.

Ambers  (y)

I know their are a lot of folks here who still don't have ambers.
We need to make sure they don't leave the GTG without them.
 
Dluvr22 said:
I can't believe we all forgot this one.

Ambers  (y)

I know their are a lot of folks here who still don't have ambers.
We need to make sure they don't leave the GTG without them.

I like your thinking. (y)
 
Does anyone want Sail Panel lights on a 2013 or a EXT.  ???
 
MS03 2500 said:
Does anyone want Sail Panel lights on a 2013 or a EXT.  ???

I have to re-glue a couple of mine in place.  They still work, just stick out a bit because the silicone I used wore off.

I also want to (if possible) replace my water pump, and relocate my train horns to a spot under the hood.

And last but not least, I have the illuminated door locks with the AV logo on them on all 4 doors, but only the two rear ones light up.  Need to connect the wires for the two in the front.
 
I just redid mine with the LEDs and the retainer in the eBay auction Douglas Oak mentioned above after having them on for 4 years.
I would highly recommend using them.

1. These LEDS and retainer fit flush in the clips for the cladding. The top of the LEDs are flat and not round like the ones we had available years ago.
2. These LEDs are also super bright LEDs and are much brighter with better light dispersion than the last set I had.

Also I have been through a few car washes since and my clips have stayed in place.
My previous set used to come out once in a while and I have had to make a few trips to my local dealer to replace clips at $7.00 a pop

If you're going to take the time to work on yours you may want to consider this option.


 
I'm bringing the same ones.  I ordered a few extras too
 
Looks like Sail panels are being done...are there going to be extra sets there and available if so I want one...if not got to order some...Mine are just a re wire... If I remember correctly there were some diodes involved in the install,which if any are needed?
 
I used the same type of diodes that we use for the FTDRL's and All-4-On-High mods....  I know the All-4-On-Brake mod uses bigger diodes.

I have a few extra diodes (for Sail Panels) and some resistors as well (to get the parking light/turn signal/brake light part of the sail panels done...

I remember the resistors are 330ohm.  Diodes MIGHT BE the 1N914 / 1N4148 type from Radio Shack (their Part# 276-1122, for a pack of 10).
 
Troublemaker said:
I used the same type of diodes that we use for the FTDRL's and All-4-On-High mods....  I know the All-4-On-Brake mod uses bigger diodes.

I have a few extra diodes (for Sail Panels) and some resistors as well (to get the parking light/turn signal/brake light part of the sail panels done...

I remember the resistors are 330ohm.  Diodes MIGHT BE the 1N914 / 1N4148 type from Radio Shack (their Part# 276-1122, for a pack of 10).

I have some extras too that I'll bring.  Not sure if they were for the all-4-on or my sail panels
 
BnGBleeder said:
Looks like Sail panels are being done...are there going to be extra sets there and available if so I want one...if not got to order some...Mine are just a re wire... If I remember correctly there were some diodes involved in the install,which if any are needed?
If you order the ones on the eBay auction listed above you will not require resistors. They come per wired for 12v .
 
Do I need to bring the 2.5T jack?
 
Back
Top