What did you do to your Avalanche today?

[BainMan]

Thanks EXT, I plan to flush with water & scrub with a toothbrush first and then use some kind of cleaner like you show.

MS03 if you want to check, you can gain access from under the passenger dash. Small part you can remove and gain a small 2"x3" viewing port. You can see inside while recording with your phone if you don't have a borescope.

 

[MS03 2500]

Thx I have a inspection camera that should work.

 

[MS03 2500]

On a side note I got into it today and notice it was blowing cold air on,a 50ish degree day. So I put it on my test software and notice this.

 

[BainMan]

Why the 0.0 reading or does that sensor not work?

 

[MS03 2500]

Appearently not I would think it should be 50ish, I'm going to try with a different app tomorrow

Oh yeah  the temp in the rearview is correct

 

[Z66Modder]

Apparently not I would think it should be 50ish, I'm going to try with a different app tomorrow

Oh yeah  the temp in the rearview is correct

Any luck?

 

[MS03 2500]

Any luck?

Nope I tried obd fusion and it still did not read. I tried to find the sensor and it was not behind the right headlight like the manual stated.

 

[MS03 2500]

Tried a few more things, still nothing

 

[EXT4ME]

I removed the optional thick black rubber floor mats that came from the factory in my 2003 Avalanche Z-66.

RPO B37.

I installed my early Father's Day present from my daughter, a full set of black WeatherTech floor mats.

I have the WeatherTech's in all of our other trucks.

These new ones are even better than the older ones.

I like!

 

[Loggie]

Took her for an oil change and rotate/balanced tires

 

[ygmn]

Walked by her when I went into garage for soemthing....

MAde sure the trickle charger still charging away....

 

[EXT4ME]

I grabbed a chair and sat down behind the tailgate and removed the dealer sticker that had been there since the truck was new back 2003.

That's enough for one day.

 

[Loggie]

removed the dealer sticker

i need to do that

 

[BainMan]

I went a little further and debadged...

I really dig the clean look!

But i ran into a little surprise, well 4 little surprises... I guess the Chevy emblem (or something) goes back or I need to get a little body work done...

 

[Z66Modder]

Can always make it a black bowtie.

 

[BainMan]

Can always make it a black bowtie.

Exactly! I thought about blacking it out anyway before I decided to debadge. Eventually I'll get a sheet of vinyl and black out the front bowtie too.

 

[EXT4ME]

I was going to check the fuel pressure.

Ended up hauling a new water heater home from Home Depot.

I am not sure which project may have ended up costing more.

 

[ygmn]

First Saturday of the month = time to crank her up and spend an 30-60mins driving the avy.

probably will end up at Home Depot to get some pressure treated lumber to reinforce the fence.
Seems the winds during these rain storms is getting stronger and more often

 

[Loggie]

going to clean her up and take a trip out to the shore

 

[itsstopher]

Two done.... 10am break time.... Finish the other side after break

 

[itsstopher]

Done 

 

[EXT4ME]

Looks really good!

 

[Loggie]

Cleaned her up and the S2K

 

[Loggie]

Done 

Love it

 

[ygmn]

I do like the look Itstopher