• If you currently own, previously owned or want to own an Avalanche, we welcome you to become a member today. Membership is FREE, register now!

Rear wheel frame shield P/N?

Jimmi Z

Full Member
Joined
Jun 4, 2004
Messages
317
I notice this was missing appears to been torn off some how, otherside also looks like it could need to be replaced. Anyone ever replaced these, so far no luck finding any info P/N? etc on the net, maybe someone made their own version.
20190713-150112-001.jpg

POR-15 doing it's job protecting from rust, been what 16 years now..
20190713-150118-001.jpg
 
Maybe make one?
Is it not just a strip of plastic/rubber about 4" tall going accross the inner fender well?

not super critical
 
Yeah I know but still like to fill the gap, you're right the material is plastic and a small like roofing felt is plastic riveted on to the plastic piece in the center hung on by large square hole next time I will used the small round hole next to it and held on by retainer rivets. Not too many pick your parts junkyards with late model avalanche's and truck's, mostly early models, I would rather have the stock than make your own..Plus where to buy that material..
 
Shows the right is available, but the left is available on ebay.. Not cheap... There was also a rubber flap that was stapled to this piece in the center, doesn?t show it in the description..

93439834 - Right
93439833 - Left

https://www.gmpartsdirect.com/auto-parts/2002/chevrolet/avalanche-2500/base-trim/8-1l-v8-gas-engine/body-cat/inner-components-scat
 
Thanks for finding it but Holy crap $173 and $160 maybe I'll look into making my own if I can find the right material..

Ok Google for lowest price found these for around $86 range..
http://oemcats.com/oem-parts/93439833.html
http://oemcats.com/oem-parts/93439834.html
May order the passenger side,double check driver side plastic piece in good shape only the felt material in the center is bit chew up.
so looks like I need the passenger side only, will find some material for the felt part...
 
Look in junkyards....
I mean hs to be there on AVYS and maybe Suburbans...
 
I'll give my local pick your part Junkyard a call and see if the have any late model Avalanche's and Suburban's, seems like in my area they all go to some hidden salvage yard not seen by the public seems a bit weird all they have is early models 70,80,90 etc..
 
You can also use this body gap guard kit that's made for this exact purpose. A lot cheaper and does front and rear..



https://www.4wheelparts.com/b/suspension/body-lift-gap-guard/_/N-cm5ie
 
Thanks Randy, I was waiting for reply back from salvage yard never did, ok decided to go Daystar got 5% discount with promote code,
will post pictures arrived and installed and give feedback on quality material used..
 
I Just picked up a bunch of packages today from my friend home address. Daystar at least 5 mm thick rubber and heavy and all the necessary plastic rivets, will install once HVAC controller is done.
20190727-161935-003.jpg
 
Well I finally got around to start installing the Daystar frame guard, and nothing lines up or come close, I tried every positions and I don't see how it suppose to go on, no pictures or anything, so I'm sending it back they're going to send me a prepaid shipping label to my email, just got to print it out and drop it off any UPS store. I'll try the local junkyard again unless someone here has a junked Avalanche willing to pull parts and sell them to me..
 
Have you tried Facebook. There has been some parting out.
If you are near Oregon Craigslist has one. Have you looked local?
 
Thanks but I don't do facebook, twitter etc. I  will call the local salvage junkyards around here, if not I might just buy the one side OEM  and bite the bullet at $86.00..
 
DUCT TAPE!!
 
Back
Top